Booting to DOS from a USB memory stick

Now that the floppy disk is ancient history and optical media is not far away, it seems we still have to boot to DOS from time-to-time to perform certain tasks, whether it is to flash a BIOS, or perform some hardware diagnostics. The preferred way of doing it these days is via a USB memory stick, and the easiest way to prepare your USB memory stick to boot to DOS is via a freeware tool called Rufus.

With Rufus, a few clicks is all you need to prepare your USB memory stick to boot to DOS. It comes with two DOSes embedded: MS-DOS and FreeDOS. No extra files are needed. After you are done preparing the stick, you can simply copy the extra application files you need over via Windows Explorer, whether it is to flash the BIOS or to diagnose that network card. It is pretty straightforward.

In addition, Rufus also lets you prepare the USB memory stick to boot to supported ISO images, including Parted Magic, Ultimate Boot CD, Windows 7 Setup etc., even Windows XP Setup (but I haven't tested it).

On an unrelated note, how I came across this tool was because I found myself having to help friends repair the Dell System Restore partition, twice, within the past few months. The DSRFix tool was immensely useful for that purpose, but I needed to boot to DOS from a USB memory stick. After scouring through the dozens of arcane/complicated instructions on the Web, this was the final solution I settled on. I am putting this on record because I am pretty sure it will come in handy for me again at another time!

Comments

Hacking an analog clock to sync with NTP - Part 5

This is how it looks after I have put everything together. The Arduino sketch is available here . The 2 jumper wires soldered to the clock mechanism are connected to pins D0 and D1 on the ESP-12 (in any order). When the device first boots up, it presents an access point which can be connected to via the PC or smartphone. Once connected, the captive portal redirects the web browser to the configuration page: A custom field has been added to the WiFi configuration page to enter the current clock time in HHMMSS format. Try to set the clock time to as close to the current time as possible using the radial dial at the back of the clock so the clock will have less work to do catching up. In the config page, the HTML5 Geolocation API is also used to obtain your current location (so if your web browser asks if you would like to share your location, answer "yes"). This is then passed to the Google Time Zone API to obtain the time and DST offset of your time z...

Cooling mod for the X96 Air #2

Previously, I added a USB cooling fan to the X96 Air TV box . The problem with this mod is that the fan is always running, and it runs at full speed. Ideally, the fan should kick in only when the CPU temperature is above a certain threshold. It would be even better if there is a way to control the fan speed. Dan McDonald left me a comment pointing to his project on Github . He basically connected the fan to a USB relay that can be controlled by Python script. His project inspired me to make a similar mod that would make use of the spare D1 Mini boards I have lying around. The plan is to hook up the fan to a MOSFET (2N7000) and control it via PWM. Here's the very simple circuit: The code simply reads a single character from the serial port (0 - 9). 0 will turn the fan off, while 1 - 9 will generate a proportional PWM to drive the fan, with 1 being the lowest and 9 being the highest. Here's the Arduino code: #include <Arduino.h> void setup () { Serial . begin ( 9600 ...

Installing and customizing CoreELEC in X96 Air

I previously installed CoreELEC on another TV Box ( Ugoos X3 Pro ), which unfortunately died after only 9 months during the summer (due to the unit overheating, which I learned is a common problem for cheap Android TV boxes). So this time I purchased a X96 Air (4GB/32Gb) and had to do the whole thing again. So this is a note-to-self in case I ever have to install CoreELEC again on some other device. Installation of CoreELEC is simple enough by following this guide . Basically, it involves downloading and writing the firmware to a microSD card using usbimager . Then insert the microSD card, reset the unit and hold the reset until the logo appears. The unit will then proceed to boot into CoreELEC. First thing is to connect to WiFi, then enable SSH. This allows me to login via ssh and execute: ceemmc -x from the terminal. This writes CoreELEC to the built-in eMMC storage, after which I am able to remove the microSD card and reboot the unit into CoreELEC via the built-in sto...

Random Sequence

Search This Blog