Hooking up USBasp programmer to the ATTiny85

After putting off the ESPClock project for quite a looooong while, I finally decided to pick up the project again.

But the Arduino Uno board had been siphoned off by my eldest son for one of his science projects, so I decided to pick up a cheap USPasp clone off eBay to help with programming the ATTiny85.

First off is to connect the 2x5 ISP header to the ATTiny85. It was a bit confusing at first, but after some research, here are the connections required.

I plugged the wires into the 10-pin ISP header, and soldered the other ends to two 1x4 male headers in the correct order. That way, I can just plug the male headers into the breadboard alongside the ATTiny85 quite easily to start programming it without too much fiddling.

I had to strengthen the soldering with some hot glue to prevent the wires from breaking off the headers when plugging them in and out repeatedly. Works a treat so far.

Then choose "USBasp" as the programmer under the Arduino IDE:

I was getting this error when trying to upload a test "Blink" sketch:

avrdude: error: could not find USB device with vid=0x16c0 pid=0x5dc vendor='www.fischl.de' product='USBasp'

This was resolved by the solution given here:

Downloading Zadiag from http://zadig.akeo.ie/
Start zadig
Options > List all devices
Select USBasp from the drop down menu
Select libusbK(v3.0.7.0) driver
Click Install

I was then able to upload the "Blink" sketch and confirms that the USBasp programmer works as advertised.

ESPCLOCK1 / ESPCLOCK2 / ESPCLOCK3 / ESPCLOCK4

Comments

Update: Line adapter for Ozito Blade Trimmer

Update (Dec 2021): If you access to a 3D printer, I would now recommend this solution , which makes it super easy to replace the trimmer line. I have been using it for a few months now with zero issue.

Cooling mod for the X96 Air

I realized after my Ugoos box died that overheating is a big problem with cheap Android TV boxes. A teardown of the Ugoos box shows that it does not have any heatsink or fan at all! The X96 Air does have a heatsink, but the heatsink is located at the bottom of the casing with no ventilation. In this default configuration, with the ambient room temperature at 25c and playing a 1080p video, I was seeing the CPU temperature at 67c. I drilled a couple of holes at the bottom of the casing. The CPU temperature fell to 59c with the box raised about 2cm with plastic blocks. I retrieved an old 5V laptop fan: Then cut and strip away a spare USB cable: Solder the red and black wires on the fan and the cable: Secure the fan to the bottom of the casing with double-sided tape, then plug the fan into the box's USB connector. Here's a view of the box with some 3D-printed risers installed at the bottom to give the mounted fan sufficient clearance: The CPU now runs at 43c, a huge drop from the ...

Installing and customizing CoreELEC in X96 Air

I previously installed CoreELEC on another TV Box ( Ugoos X3 Pro ), which unfortunately died after only 9 months during the summer (due to the unit overheating, which I learned is a common problem for cheap Android TV boxes). So this time I purchased a X96 Air (4GB/32Gb) and had to do the whole thing again. So this is a note-to-self in case I ever have to install CoreELEC again on some other device. Installation of CoreELEC is simple enough by following this guide . Basically, it involves downloading and writing the firmware to a microSD card using usbimager . Then insert the microSD card, reset the unit and hold the reset until the logo appears. The unit will then proceed to boot into CoreELEC. First thing is to connect to WiFi, then enable SSH. This allows me to login via ssh and execute: ceemmc -x from the terminal. This writes CoreELEC to the built-in eMMC storage, after which I am able to remove the microSD card and reboot the unit into CoreELEC via the built-in sto...

Random Sequence

Search This Blog