Skip to main content

MIUI: Connecting to MJX Bugs B2W

I recently purchased the MJX Bugs B2W drone, and had a lot of difficulty connecting to the onboard 5GHz WIFI camera from the Bugs Go app. I finally figured out the solution, and it was totally unexpected, so I thought I'd share it here for anyone faced with the same issue.

I am using the Redmi Note 4 to connect, and that phone supported 5GHz WIFI, so I had no problem connecting to the drone hotspot. But when I launched the Bugs Go app, I keep getting the "Aircraft not connected" message. I tried a couple of stuff, including resetting the 5GHz channel used by the drone (by pressing on the "Camera" button on the remote controller for about 8 seconds, until you hear 3 beeps). Nothing worked.

Then I realized when I connect to the drone hotspot and run Bugs Go, I see this message:


It didn't occur to me initally to tap on the message, because I already knew the drone hotspot had no Internet acess. So out of desperation, I tapped on the message:


By selecting "Stay connected", Bugs Go was immediately able to connect to the drone and started streaming the live video feed from the camera.

Lesson learned!

Labels:

Comments

  1. Beto27 August 2018 at 06:28

    Great man! I'm having the same problem! will give it a try!

    ReplyDelete
  2. EPlan19 December 2019 at 05:49

    You just saved me a lot of frustration. Having the same problem and your guidance fixed it. Thank you!

    ReplyDelete

Post a Comment

Popular posts from this blog

Update: Line adapter for Ozito Blade Trimmer

Update (Dec 2021): If you access to a 3D printer, I would now recommend this solution , which makes it super easy to replace the trimmer line. I have been using it for a few months now with zero issue.
5 comments
Read more

Cooling mod for the X96 Air

I realized after my Ugoos box died that overheating is a big problem with cheap Android TV boxes. A teardown of the Ugoos box shows that it does not have any heatsink or fan at all!  The X96 Air does have a heatsink, but the heatsink is located at the bottom of the casing with no ventilation. In this default configuration, with the ambient room temperature at 25c and playing a 1080p video, I was seeing the CPU temperature at 67c. I drilled a couple of holes at the bottom of the casing. The CPU temperature fell to 59c with the box raised about 2cm with plastic blocks. I retrieved an old 5V laptop fan: Then cut and strip away a spare USB cable: Solder the red and black wires on the fan and the cable: Secure the fan to the bottom of the casing with double-sided tape, then plug the fan into the box's USB connector. Here's a view of the box with some 3D-printed risers installed at the bottom to give the mounted fan sufficient clearance: The CPU now runs at 43c, a huge drop from the ...
2 comments
Read more

Installing and customizing CoreELEC in X96 Air

I previously installed CoreELEC on another TV Box ( Ugoos X3 Pro ), which unfortunately died after only 9 months during the summer (due to the unit overheating, which I learned is a common problem for cheap Android TV boxes). So this time I purchased a X96 Air  (4GB/32Gb) and had to do the whole thing again. So this is a note-to-self in case I ever have to install CoreELEC again on some other device. Installation of CoreELEC is simple enough by following this guide . Basically, it involves downloading and writing the firmware to a microSD card using usbimager . Then insert the microSD card, reset the unit and hold the reset until the logo appears. The unit will then proceed to boot into CoreELEC. First thing is to connect to WiFi, then enable SSH. This allows me to login via ssh and execute: ceemmc -x from the terminal. This writes CoreELEC to the built-in eMMC storage, after which I am able to remove the microSD card and reboot the unit into CoreELEC via the built-in sto...
Post a Comment
Read more